SENSIT Technologies HXG-2 Manuale di programmazione

Quick-Start Instructions

HINT: As you approach the source of the

leak continue adjusting the wheel without

moving the sensor head to a uniform tick

sound until you locate the exact location of

the leak.

IMPORTANT: When replacing the

gooseneck into the clip on the right side,

wrap the gooseneck in a wide circular

manner counter-clockwise around the back

of the instrument. Bending in the opposite

direction may cause damage over the life of

the product.

WARNINGS:

To prevent ignition of ammable or

combustible atmospheres, disconnect power

before servicing.

Always change batteries in an environment

free of combustible gases.

This instrument should not be used as a

carbon monoxide investigative tool.

This is not a substitute for the

instruction manual. It is for

reference only.

Read and understand the

instruction manual before use.

MADE IN THE USA

WITH GLOBALLY SOURCED COMPONENTS

Distributed by:

851 Transport Drive

Valparaiso, IN 46383-8432

Phone: 219 465 2700

Web: www.gasleaksensors.com

Innovative Detection Solutions

1. Install the batteries by pushing down

the locking tab and sliding the handle

away from the top of the instrument. When

replacing handle be sure the tab is securely

in place and replace the retaining screw.

2. IMPORTANT: CAREFULLY OBSERVE

POLARITY WHEN CHANGING BATTERIES.

Instrument will not function with improperly

installed batteries.

3. Slide the on/off switch to the right to turn on.

4. Allow unit to go through the warm up

sequence in clean air. The tick will sound

and the alarm light will ash for a few

moments. Full warm up may take up to 60

seconds.

5. Extend the goose neck (the sensor and

cap is at the tip).

6. You are now ready to use the instrument.

You can now enter the area and detect gases.

7. A properly tested and calibrated

instrument will ash the red alarm light and

provide a warbling sound at 10% LEL of

methane. Consult Sensit Technologies for

cross sensitivities.

8. Once the environment is determined to

be safe to work in, if the source of an odor

needs to be located, rotate the center wheel

until there is a uniform ticking sound. As

you approach the leak rotate the wheel

counter-clockwise to slow the speed. Rotate

clockwise to increase the speed (indicating

lower gas concentrations).

9. When your investigation is complete slide

the switch to the off position.

SENSIT®HXG-2

QUICK-START INSTRUCTIONS

Altri manuali SENSIT Technologies Strumento di misura

SENSIT Technologies

SENSIT Technologies GOLD 100 Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GOLD EXCO+1200 Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GLT Manuale di programmazione

SENSIT Technologies

SENSIT Technologies HXG-3P Manuale di programmazione

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Manuale utente

SENSIT Technologies

SENSIT Technologies Trak-It IIIa GLT Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GAS-TRAC LZ-30 Manuale utente

SENSIT Technologies

SENSIT Technologies IRED Manuale di programmazione

SENSIT Technologies

SENSIT Technologies CO Manuale di programmazione

SENSIT Technologies

SENSIT Technologies HCN Manuale di programmazione

SENSIT Technologies

SENSIT Technologies HXG-3 Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GOLD CGI Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GOLD Manuale di programmazione

SENSIT Technologies

SENSIT Technologies Trak-It IIIa GLT Manuale utente

SENSIT Technologies

SENSIT Technologies GAS-TRAC LZ-30 Manuale di programmazione

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Manuale utente

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Manuale utente

SENSIT Technologies

SENSIT Technologies SPOD Guida rapida

SENSIT Technologies

SENSIT Technologies SENSIT GOLD G2 Manuale utente

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Manuale di programmazione

SENSIT Technologies

SENSIT Technologies P400 Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GOLD CGI Manuale di programmazione

SENSIT Technologies

SENSIT Technologies HXG-2d Manuale di programmazione

SENSIT Technologies

SENSIT Technologies Trak-It IIIa Manuale di programmazione

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente