Ultimaker 3 Extended Guida

Ultimaker Support

›

3D Printers

›

Ultimaker 3

›

Maintenance

Check for play on the axles of the

Ultimaker 3

January 28, 2020 10:31

The four X and Y axles are locked in place by the pulleys. However, it is possible that one

or more of the pulleys can become slightly loose over time, which could affect their

alignment. If this is the case, there could be play on the X and/or Y axles which can cause

issues with print quality.

It is recommended to check for play on the axles at least once every three months.

Start with the right X axle. Place the print head in the back-left corner of the printer to

keep it out of the way. Hold the frame of the Ultimaker 3 with one hand, and firmly hold

the right X axle with the other. Attempt to move the axle forwards and backwards; do

not be afraid to apply too much force.

Ultimaker

Ask our community of experts

Go to our community











Check for play on the axles of the Ultimaker 3 – ... https://support.ultimaker.com/hc/en-us/articles/...

1 of 3 12/15/20, 1:54 PM

Comments

0 comments

Article is closed for comments.

Articles in this section

Repeat this for the other axles. Make sure to move the print head to the opposite side

each time.

The axles should not move at all. If one of the axles does move, you can observe a

ticking noise of the pulleys hitting the frame. In this case it is recommended to

calibrate

the print head

Was this article helpful?





0 out of 8 found this helpful



Update the Ultimaker 3 firmware



Ultimaker 3 firmware release notes



Replace the build plate clamps of the Ultimaker 3



Replace the radial fans of the Ultimaker 3



Replace the axial fan of the Ultimaker 3



Replace the tube coupling collet of the Ultimaker 3



Replace the clamp clip of the Ultimaker 3



Replace the Bowden tubes on the Ultimaker 3



Clean the feeders on the Ultimaker 3



Lubricate the lead screw of the Z motor on the Ultimaker 3

Check for play on the axles of the Ultimaker 3 – ... https://support.ultimaker.com/hc/en-us/articles/...

2 of 3 12/15/20, 1:54 PM

Recently viewed articles



Lubricate the Ultimaker 3 axles



Cleaning the Ultimaker 3



Ultimaker 3 maintenance schedule

Check for play on the axles of the Ultimaker 3 – ... https://support.ultimaker.com/hc/en-us/articles/...

3 of 3 12/15/20, 1:54 PM

Altri manuali per 3 Extended

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ultimaker Stampante 3D

Ultimaker

Ultimaker Original Manuale utente

Ultimaker

Ultimaker 2 Extended Manuale utente

Ultimaker

Ultimaker 3 Extended Guida

Ultimaker

Ultimaker 3 Extended Manuale utente

Ultimaker

Ultimaker S5 Material Station Manuale utente

Ultimaker

Ultimaker ORIGINAL+ Manuale utente

Ultimaker

Ultimaker 2 Go Manuale utente

Ultimaker

Ultimaker Heated Bed Upgrade Kit Manuale utente

Ultimaker

Ultimaker 3 Extended Manuale utente

Ultimaker

Ultimaker ORIGINAL+ Manuale utente

Ultimaker

Ultimaker Ultimaker S5 Pro Bundle Manuale utente

Ultimaker

Ultimaker 2 Extended Manuale utente

Ultimaker

Ultimaker 3 Extended Guida alla configurazione

Ultimaker

Ultimaker S5 Material Station Manuale utente

Ultimaker

Ultimaker ORIGINAL+ Manuale utente

Ultimaker

Ultimaker 3 Extended Manuale utente

Ultimaker

Ultimaker 2 Extended Manuale utente

Ultimaker

Ultimaker S3 Manuale utente

Ultimaker

Ultimaker EXTRUSION UPGRADE Manuale utente

Ultimaker

Ultimaker EXTRUSION UPGRADE Manuale utente

Ultimaker

Ultimaker 2 Extended Manuale utente

Ultimaker

Ultimaker S3 Guida all'installazione

Ultimaker

Ultimaker 3 Extended Guida

Ultimaker

Ultimaker 2+ Connect Manuale per l'uso e la cura

Manuali Stampante 3D popolari di altre marche

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente

LONGER

LONGER LK4 Pro Manuale utente