Uplus Lighting COB400 ZOOM Manuale utente

User manual

COB400 ZOOM

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions……………………………………………………………………………3-4

2.Technical Specifications…………………………………………………………………………4

3.Control Menu ………………………………………………………………………………………5

4.DMX Channels ……………………………………………………………………………………6

5.Trouble Shooting…………………………………………………………………………………6

6.Fixture Cleaning………………………………………………………… ………………………7

STATEMENT

The product has well capability and intact packing when leave factory. All of the user should

comply with warning item and manual, any misuse cause of the damages are not included in our

guarantee, and also can not be responsible for any malfunction & problem owing to ignore the

manual.

1.Safety Instructions

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

•Unpack and check carefully there is no transportation damage before using the unit.

•Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

•The unit is for indoor use only. Use only in a dry location.

•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

•Disconnect main power before replacement or servicing.

•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand

during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit

by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

•DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:

•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to

which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people.

2.Technical Specifications

VOLTAGES:AC 100V-240V，50/60Hz

POWER CONSUMPTION:450W@230V

Light Source: 400W White COB Led

Quantity: 1pcs

Color Wheel: 4 colors and Open （R+G+B+WW）or CTO Color temperature 2800-6000K(Selectable)

DIMMER:0-100% mechanical dimming, free dimming available, macro control

STROBE: （Optional）

Electronic Strobe 0 -25F.P.S

IP RATE:IP20 Indoor

BEAM ANGLE: 6-50°

CONTROL:DMX512, 3 pins interfaces RDM Control Protocol

Channel mode: 10 Channel

Pan scan：540°(16bit) Electric correction

Tilt scan：270° (16bit) Electric correction

Control Mode:DMX512 / Master-Slave / Auto

HOUSING:Cast aluminum, IP20 Indoor

WORK ENVIRONMENT TEMPERATURE: -10°C-40°C

Dimension: 300 * 220 * 470mm;

Net weight : 9.7Kg

Carton Size: 60*41*34cm

3.Control Menu

Operation method

touch

wheel

function

turn left

option/edit

down

turn right

option/edit

OK / Enter

press the wheel

Executive start / exit

return

when return menu ,press the wheel

return previous page

Set ”Modify address code” as an example, tell about the using of the touch.

1. Touch button “setting” in the main interface, and then into “setting” interface.

2. The 4 touch button in the right, are “up”, “ok”, “down”, “back”.

3. Press “up” or “down” button select “DMX address”.

4. Press “ok” button into editing state.

5. Press “up” button or “ down” button modification address code (using the new address immedi

ately and autosave)

6.Press “OK” button out of the editing state ( could omitted)

7. Press “back” button back to the main menu.

If using the wheel, process like bellow :

1. In the main interface , turn the wheel, select “setting” button.

2. Press the turn wheel and then loosen, into “setting” interface.

3.In the “setting” interface, select “DMX address”

4. Press the turn wheel and then loosen, into the editing state.

5. Turn the wheel, modification address code

6. After modification, press turn wheel and then loosen, out of the editing state.

7. Turn the wheel select “back”, press turn wheel and then loosen, back into the main interface.

4.DMX Channels

10 Channel mode

Channel

Name

DMX Value

Description

Pan

0-255

Pan Movement

Pan Fine

0-255

Pan Fine

Tilt

0-255

Tilt Movement

Tilt Fine

0-255

Tilt Fine

P/T SPEED

0-255

P/T SPEED

ZOOM

0-255

ZOOM

CTO

0-255

Change Color temperature (2600-6500K)

Dimmer

0-255

Dimmer from dark to bright

STROBE

0-5

OPEN

6-10

CLOSED

252-255

STROBE FORM SLOW TO FAST

RESET

250-255

Reset after 3 seconds

5.Trouble Shooting

ollo

ing

few

oble

occu

uring

ope

tion

leshooting

The

does

work

ght

Check

nect

ion of p

owe

eas

ure

ins

volt

Check

pow

LED

responding

LED

on.

che

nectors,

link

ope

espons

el,

che

ess

etti

ity

nter

ittent

oble

che

ins

onn

ecto

PCB

nit

the

iou

ntroller

Check

or run

lon

volta

les

terfer

ence

inter

face

circui

One

the

cha

ing

tep

moto

dam

the

nect

PCB

oken.

oto

’

ive

PCB

ndition

6.Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to

optimize light output. Cleaning frequency depends on the environment in which the fixture operates:

damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.

Clean with soft cloth using normal glass cleaning fluid.

Always dry the parts carefully.

Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

Indice

Altri manuali Uplus Lighting Attrezzatura di illuminazione

Uplus Lighting

Uplus Lighting LED PROFILE MZ Manuale utente

Uplus Lighting

Uplus Lighting 280 LED BSW Manuale utente

Uplus Lighting

Uplus Lighting W1925 Manuale utente

Uplus Lighting

Uplus Lighting 360 BEAM Manuale utente

Uplus Lighting

Uplus Lighting DUAD540 STROBE Manuale utente

Uplus Lighting

Uplus Lighting MH12X40 PIXEL BAR Manuale utente

Uplus Lighting

Uplus Lighting 200 BLINDER Manuale utente

Uplus Lighting

Uplus Lighting 200 LED BSW Manuale utente

Uplus Lighting

Uplus Lighting IP-L360 Manuale utente

Uplus Lighting

Uplus Lighting 4020 IP Manuale utente

Uplus Lighting

Uplus Lighting 250 LED BEAM Manuale utente

Uplus Lighting

Uplus Lighting BR360 Manuale utente

Uplus Lighting

Uplus Lighting 200 LED BSW Manuale utente

Uplus Lighting

Uplus Lighting 750 BSWF Manuale utente

Uplus Lighting

Uplus Lighting LED PROFILE FIX Manuale utente

Uplus Lighting

Uplus Lighting IP MATRIX 5 Manuale utente

Uplus Lighting

Uplus Lighting 200 LED RETRO Manuale utente

Uplus Lighting

Uplus Lighting 100SPOT Manuale utente

Uplus Lighting

Uplus Lighting 3010 IP PAR Manuale utente

Uplus Lighting

Uplus Lighting 19X15Z WASH Manuale utente

Uplus Lighting

Uplus Lighting W3725 Manuale utente

Uplus Lighting

Uplus Lighting RETRO 360 Manuale utente

Uplus Lighting

Uplus Lighting BSW 350 Manuale utente

Uplus Lighting

Uplus Lighting MIX560 Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente