Agilent Technologies E4419B Manuale utente

Agilent Technologies Part no. E4419-90006

December, 1998

User’s Guide

Agilent Technologies

E4419B Power Meter

HP4402.book Page i Thursday, November 30, 2000 1:39 PM

ii Agilent E4419B User’s Guide

written permission is prohibited, except as allowed under the copyright

laws.

Printed in the UK.

HP4402.book Page ii Thursday, November 30, 2000 1:39 PM

Legal Information

Agilent E4419B User’s Guide iii

Legal Information

Notice

Information contained in this document is subject to change without

notice. Agilent Technologies makes no warranty of any kind with regard to

this material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Agilent Technologies

shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishings, performance,

or use of this material. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written

consent of Agilent Technologies.

Certification

Agilent Technologies certifies that this product met its published

specifications at the time of shipment from the factory. Agilent

Technologies further certifies that its calibration measurements are

traceable to the United States National Institute of Standards and

Technology, to the extent allowed by the Institute’s calibration facility, and

to the calibration facilities of other International Standards Organization

members.

Warranty

This Agilent Technologies instrument product is warranted against

defects in material and workmanship for a period of one year from date of

shipment. During the warranty period, Agilent Technologies will at its

option, either repair or replace products which prove to be defective. For

warranty service or repair, this product must be returned to a service

facility designated by Agilent Technologies. Buyer shall prepay shipping

charges to Agilent Technologies and Agilent Technologies shall pay

shipping charges, duties, and taxes for products returned to Aglent

Technologies from another country. Agilent Technologies warrants that its

software and firmware designated by Agilent Technologies for use with an

instrument will execute its programming instructions when properly

installed on that instrument. Agilent Technologies does not warrant that

the operation of the instrument, or firmware will be uninterrupted or

error free.

HP4402.book Page iii Thursday, November 30, 2000 1:39 PM

Legal Information

iv Agilent E4419B User’s Guide

Limitation of Warranty

The foregoing warranty shall not apply to defects resulting from improper

or inadequate maintenance by Buyer, Buyer-supplied software or

interfacing, unauthorized modification or misuse, operation outside of the

environmental specifications for the product, or improper site preparation

or maintenance. NO OTHER WARRANTY IS EXPRESSED OR IMPLIED.

HP SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Exclusive Remedies

THE REMEDIES PROVIDED HEREIN ARE BUYER’S SOLE AND

EXCLUSIVE REMEDIES. AGILENT TECHNOLOGIES SHALL NOT BE

LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES, WHETHER BASED ON CONTRACT,

TORT, OR ANY OTHER LEGAL THEORY.

HP4402.book Page iv Thursday, November 30, 2000 1:39 PM

Equipment Operation

Agilent E4419B User’s Guide v

Equipment Operation

Warnings and Cautions

This guide uses warnings and cautions to denote hazards.

WARNING A warning calls attention to a procedure, practice or the

like, which, if not correctly performed or adhered to, could

result in injury or the loss of life. Do not proceed beyond a

warning until the indicated conditions are fully

understood and met.

Caution A caution calls attention to a procedure, practice or the like which,

if not correctly performed or adhered to, could result in damage to

or the destruction of part or all of the equipment. Do not proceed

beyond a caution until the indicated conditions are fully

understood and met.

Personal Safety Considerations

WARNING This is a Safety Class I product (provided with a protective

earthing ground incorporated in the power cord). The

mains plug shall only be inserted in a socket outlet

provided with a protective earth contact. Any interruption

of the protective conductor, inside or outside the

instrument, is likely to make the instrument dangerous.

Intentional interruption is prohibited.

If this instrument is not used as specified, the protection

provided by the equipment could be impaired. This

instrument must be used in a normal condition (in which

all means of protection are intact) only.

No operator serviceable parts inside. Refer servicing to

qualified personnel. To prevent electrical shock, do not

remove covers.

For continued protection against fire hazard, replace the

line fuse(s) only with fuses of the same type and rating (for

example, normal blow, time delay, etc.). The use of other

fuses or material is prohibited.

HP4402.book Page v Thursday, November 30, 2000 1:39 PM

General Safety Considerations

vi Agilent E4419B User’s Guide

General Safety Considerations

WARNING Before this instrument is switched on, make sure it has

been properly grounded through the protective conductor

of the ac power cable to a socket outlet provided with

protective earth contact.

Any interruption of the protective (grounding) conductor,

inside or outside the instrument, or disconnection of the

protective earth terminal can result in personal injury.

Caution Any adjustments or service procedures that require operation of

the instrument with protective covers removed should be

performed only by trained service personnel.

Markings

The CE mark shows that the product complies with

all the relevant European legal Directives (if

accompanied by a year, it signifies when the design

was proven.

This is the symbol of an Industrial Scientific and

Medical Group 1 Class A product.

The CSA mark is a registered trademark of the

Canadian Standards Association.

External Protective Earth Terminal.

While this is a Class I product, provided with a

protective earthing conductor in a power cord, an

external protective earthing terminal has also been

provided. This terminal is for use where the earthing

cannot be assured. At least an 18AWG earthing

conductor should be used in such an instance, to

ground the instrument to an assured earth terminal.

ISMGROUP 1

CLASS A

HP4402.book Page vi Thursday, November 30, 2000 1:39 PM

General Safety Considerations

Agilent E4419B User’s Guide vii

IEC 1010-1 Compliance

This instrument has been designed and tested in accordance with IEC

Publication 61010-1 +A1:1992 Safety Requirements for Electrical

Equipment for Measurement, Control and Laboratory Use and has been

supplied in a safe condition. The instruction documentation contains

information and warnings which must be followed by the user to ensure

safe operation and to maintain the instrument in a safe condition.

Statement of Compliance

This product has been designed and tested for compliance with IEC 60529

(1989) Degrees of Protection Provided by Enclosures (IP Code). Level IPx4

is attained if, and only if, the carry case (Agilent Technologies part

number 34141A) is fitted.

User Environment

This product is designed for use in a sheltered environment (avoiding

extreme weather conditions) in accordance with Pollution Degree 3

defined in IEC 60664-1, with the carry case (Agilent Technologies part

number 34141A) fitted over the instrument.

The product is suitable for indoor use only, when this carry case is not

fitted.

Installation Instructions

To avoid unnecessary over-temperature conditions, while this carry case is

fitted do not apply an ac mains supply voltage, only operate your Agilent

Technologies E4419B from the battery pack.

HP4402.book Page vii Thursday, November 30, 2000 1:39 PM

Regulatory Information

viii Agilent E4419B User’s Guide

Regulatory Information

Sound Emission

Herstellerbescheinigung

Diese Information steht im Zusammenhang mit den Anforderungen der

Maschinenlarminformationsverordnung vom 18 Januar 1991.

•Sound Pressure LpA < 70 dB.

•Am Arbeitsplatz.

•Normaler Betrieb.

•Nach DIN 45635 T. 19 (Typprufung).

Manufacturers Declaration

This statement is provided to comply with the requirements of the

German Sound DIN 45635 T. 19 (Typprufung).

•Sound Pressure LpA < 70 dB.

•At operator position.

•Normal operation.

•According to ISO 7779 (Type Test).

Australian EMC Regulations

The C-Tick mark is a registered trademark of the Spectrum Management

Agency of Australia. This signifies compliance with the Australian EMC

Framework Regulations under the terms of the Radiocommunications Act

of 1992.

N279

HP4402.book Page viii Thursday, November 30, 2000 1:39 PM

Regulatory Information

Agilent E4419B User’s Guide ix

Europe Contact:

Your local Agilent Technologies Sales and Service Office or Agilent Technologies GmbH, Department 2Q /

Standards Europe, Herrenberger Strasse 130, D7030 Boblinger (Fax; +49-7031-143143).

Declaration of Conformity

according to ISO/IEC Guide 22 and EN45014

Manufacturer’s Name: Agilent Technologies

Manufacturer's Address: South Queensferry

West Lothian, EH30 9TG

Scotland, United Kingdom

Declares that the product

Product Name:Dual Channel Power Meter

Model Numbers: Agilent E4419B

Product Options: This declaration covers all options of the above products as detailed in

TCF A-5951-9852-02

Conforms with the protection requirements of European Council Directive 89/336/EEC on the approximation

of the laws of the member states relating to electromagnetic compatibility.

Against EMC test specifications EN 55011:1991 (Group 1, Class A) and EN 50082-1:1992

As Detailed in: Electromagnetic Compatibility (EMC)

Technical Construction File (TCF) No. A-5951-9852-01

Assessed by: Dti Appointed Competent Body

EMC Test Centre,

GEC-Marconi Avionics Ltd.,

Maxwell Building,

Donibristle Industrial Park,

KY11 5LB

Scotland, United Kingdom

Technical Report Number:6893/2200/CBR, dated 23 September 1997

Supplementary Information: The product conforms to the following safety standards

EN61010-1 (1993) / IEC 1010-1 (1990) + A1 (1992)

CSA-C22.2 No. 1010.1-92

EN60825-1 (1994) / IEC 825-1 (1993)

The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC, and carries the

CE-marking accordingly. This product is also designed to meet IPx4 in accordance with IEC 60529:1989 / EN

60529:1992.

South Queensferry, Scotland 22 October 1998

Location Date R.M. Evans / Quality Manager

HP4402.book Page ix Thursday, November 30, 2000 1:39 PM

List of Related Publications

x Agilent E4419B User’s Guide

List of Related Publications

The Agilent E4419B is also available in the following languages:

•English Language User’s Guide - Standard

•German Language User’s Guide - Option ABD

•Spanish Language User’s Guide - Option ABE

•French Language User’s Guide - Option ABF

•Italian Language User’s Guide - Option ABZ

•Japanese Language User’s Guide - Option ABJ

Agilent Technologies E4418B/E4419B Programming Guide is shipped as

standard.

Agilent Technologies E4418B/E4419B Service Guide is available by

ordering Option 915.

Agilent Technologies E4418B/E4419B CLIPs (Component Location and

Information Pack) is available by ordering E4418-90031.

Useful information on SCPI (Standard Commands for Programmable

Instruments) can be found in:

•A Beginner’s Guide to SCPI, which is available by ordering Agilent

Technologies Part Number 5010-7166.

•The SCPI reference manuals which are available from:

SCPI Consortium,

8380 Hercules Drive, Suite P3,

La Mesa, CA 91942, USA.

Telephone: 619-697-4301

Fax: 619-697-5955

HP4402.book Page x Thursday, November 30, 2000 1:39 PM

Altri manuali per E4419B

Indice

Altri manuali Agilent Technologies Strumento di misura

Agilent Technologies

Agilent Technologies PSA Series Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies ESA-E E4404B Manuale utente

Agilent Technologies

Agilent Technologies PSA Series Manuale utente

Agilent Technologies

Agilent Technologies E5500A Manuale utente

Agilent Technologies

Agilent Technologies FRG-700 Manuale utente

Agilent Technologies

Agilent Technologies E4445A PSA Series Guida rapida

Agilent Technologies

Agilent Technologies N1911A Manuale utente

Agilent Technologies

Agilent Technologies ESA-E E4402B Manuale utente

Agilent Technologies

Agilent Technologies X Series Manuale

Agilent Technologies

Agilent Technologies Acqiris DC110 Manuale utente

Agilent Technologies

Agilent Technologies 11980A Manuale operativo

Agilent Technologies

Agilent Technologies 1680 series Manuale utente

Agilent Technologies

Agilent Technologies All Manuale

Agilent Technologies

Agilent Technologies E8363BU-014 Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies Agilent 4396B Istruzioni operative

Agilent Technologies

Agilent Technologies PNA Series Manuale utente

Agilent Technologies

Agilent Technologies 8702D Manuale utente

Agilent Technologies

Agilent Technologies 4418B Manuale utente

Agilent Technologies

Agilent Technologies 100 Manuale utente

Agilent Technologies

Agilent Technologies B1500A Guida all'installazione

Agilent Technologies

Agilent Technologies 8510C Manuale del proprietario

Agilent Technologies

Agilent Technologies PSA Series Guida rapida

Agilent Technologies

Agilent Technologies N8262A P Series Manuale utente

Agilent Technologies

Agilent Technologies 2100 Bioanalyzer System Manuale di installazione e funzionamento

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente