Agilent Technologies 8960 Manuale utente

Agilent Technologies 8960 Series 10 Wireless Communications Test Set

Manual Operation: Getting Started Guide

AMPS/136 Mobile Test Application E1961A Revision: A.05

cdma2000 Mobile Test Application E1962B Revision: B.02

GPRS Mobile Test Application E1964A Revision: A.02

GSM Mobile Test Application E1960A Revision: A.08

GSM_AMPS/136_GPRS Mobile Test Application (fast switching) E1985A Revision: A.02

Agilent Part Number: 5967-5172

Print Date: September 2001

www.agilent.com/find/8960support/

S:\Hp8960\Generic Documents\Manual Operation Getting Started Guide\Pi_manual operation getting started guide\chapters\titlepage.fm

Edition/Print Date

All Editions and Updates of this manual and their creation dates are listed below.

March 2001 - 5967-5124

July 2001 - 5967-5156

September 2001 - 5967-5172

Safety Summary

The following general safety precautions must be observed during all phases of

operation of this instrument. Failure to comply with these precautions or with

specific warnings elsewhere in this manual violates safety standards of design,

manufacture, and intended use of the instrument. Agilent Technologies Inc. assumes

no liability for the customer’s failure to comply with these requirements.

GENERAL

This product is a Safety Class 1 instrument (provided with a protective earth

terminal). The protective features of this product may be impaired if it is used in a

manner not specified in the operation instructions.

All Light Emitting Diodes (LEDs) used in this product are Class 1 LEDs as per IEC

60825-1.

This product has been designed and tested in accordance with IEC Publication 1010,

"Safety Requirements for Electronic Measuring Apparatus," and has been supplied in

a safe condition. This instruction documentation contains information and warnings

which must be followed by the user to ensure safe operation and to maintain the

product in a safe condition.

S:\Hp8960\Generic Documents\Manual Operation Getting Started Guide\Pi_manual operation getting started guide\chapters\titlepage.fm

ENVIRONMENTAL CONDITIONS

This instrument is intended for indoor use in an installation category II, pollution

degree 2 environment. It is designed to operate at a maximum relative humidity of

95% and at altitudes of up to 2000 meters. Refer to the specifications tables for the ac

mains voltage requirements and ambient operating temperature range.

Ventilation Requirements: When installing the product in a cabinet, the convection

into and out of the product must not be restricted. The ambient temperature (outside

the cabinet) must be less than the maximum operating temperature of the product by

4°C for every 100 watts dissipated in the cabinet. If the total power dissipated in the

cabinet is greater than 800 watts, then forced convection must be used.

BEFORE APPLYING POWER

Verify that the product is set to match the available line voltage, the correct fuse is

installed, and all safety precautions are taken. Note the instrument's external

markings described under Safety Symbols.

GROUND THE INSTRUMENT

To minimize shock hazard, the instrument chassis and cover must be connected to an

electrical protective earth ground. The instrument must be connected to the ac power

mains through a grounded power cable, with the ground wire firmly connected to an

electrical ground (safety ground) at the power outlet. Any interruption of the

protective (grounding) conductor or disconnection of the protective earth terminal

will cause a potential shock hazard that could result in personal injury.

FUSES

Only fuses with the required rated current, voltage, and specified type (normal blow,

time delay, etc.) should be used. Do not use repaired fuses or short-circuited fuse

holders. To do so could cause a shock or fire hazard.

DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE

Do not operate the instrument in the presence of flammable gases or fumes.

DO NOT REMOVE THE INSTRUMENT COVER

Operating personnel must not remove instrument covers. Component replacement

and internal adjustments must be made only by qualified service personnel.

Instruments that appear damaged or defective should be made inoperative and

secured against unintended operation until they can be repaired by qualified service

personnel.

S:\Hp8960\Generic Documents\Manual Operation Getting Started Guide\Pi_manual operation getting started guide\chapters\titlepage.fm

WARNING The WARNING sign denotes a hazard. It calls attention to a

procedure, practice, or the like, which, if not correctly

performed or adhered to, could result in personal injury. Do not

proceed beyond a WARNING sign until the indicated conditions

are fully understood and met.

CAUTION The CAUTION sign denotes a hazard. It calls attention to an operating

procedure, or the like, which, if not correctly performed or adhered to,

could result in damage to or destruction of part or all of the product. Do

not proceed beyond a CAUTION sign until the indicated conditions are

fully understood and met.

Safety Symbols

Caution, refer to accompanying documents

Warning, risk of electric shock

Earth (ground) terminal

Alternating current

Frame or chassis terminal

Standby (supply). Units with this symbol are not completely disconnected from ac

mains when this switch is off.

To completely disconnect the unit from ac mains, either disconnect the power cord, or

have a qualified electrician install an external switch.

S:\Hp8960\Generic Documents\Manual Operation Getting Started Guide\Pi_manual operation getting started guide\chapters\titlepage.fm

Product Markings

CE - the CE mark is a registered trademark of the European Community. A CE mark

accompanied by a year indicated the year the design was proven.

CSA - the CSA mark is a registered trademark of the Canadian Standards

Association.

CERTIFICATION

Agilent Technologies certifies that this product met its published specifications at the

time of shipment from the factory. Agilent Technologies further certifies that its

calibration measurements are traceable to the United States National Institute of

Standards and Technology, to the extent allowed by the Institute’s calibration facility,

and to the calibration facilities of other International Standards Organization

members

S:\Hp8960\Generic Documents\Manual Operation Getting Started Guide\Pi_manual operation getting started guide\chapters\titlepage.fm

Agilent Technologies Warranty Statement for

Commercial Products

Agilent Technologies 8960 Series 10 Wireless Communications Test Set,

AMPS/136 Mobile Test Application E1961A

cdma2000 Mobile Test Application E1962B

GPRS Mobile Test Application E1964A

GSM Mobile Test Application E1960A

IS-2000 Mobile Test Application E1962A

Duration of Warranty: 1 year

1. Agilent Technologies warrants Agilent Technologies hardware, accessories and supplies

against defects in materials and workmanship for the period specified above. If Agilent

Technologies receives notice of such defects during the warranty period, Agilent

Technologies will, at its option, either repair or replace products which prove to be

defective. Replacement products may be either new or like-new.

2. Agilent Technologies warrants that Agilent Technologies software will not fail to execute

its programming instructions, for the period specified above, due to defects in material and

workmanship when properly installed and used. If Agilent Technologies receives notice of

such defects during the warranty period, Agilent Technologies will replace software media

which does not execute its programming instructions due to such defects.

3. Agilent Technologies does not warrant that the operation of Agilent Technologies products

will be uninterrupted or error free. If Agilent Technologies is unable, within a reasonable

time, to repair or replace any product to a condition as warranted, customer will be

entitled to a refund of the purchase price upon prompt return of the product.

4. Agilent Technologies products may contain remanufactured parts equivalent to new in

performance or may have been subject to incidental use.

5. The warranty period begins on the date of delivery or on the date of installation if installed

by Agilent Technologies. If customer schedules or delays Agilent Technologies installation

more than 30 days after delivery, warranty begins on the 31st day from delivery.

S:\Hp8960\Generic Documents\Manual Operation Getting Started Guide\Pi_manual operation getting started guide\chapters\titlepage.fm

6. Warranty does not apply to defects resulting from (a) improper or inadequate maintenance

or calibration, (b) software, interfacing, parts or supplies not supplied by Agilent

Technologies, (c) unauthorized modification or misuse, (d) operation outside of the

published environmental specifications for the product, or (e) improper site preparation or

maintenance.

7. TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTIES ARE

EXCLUSIVE AND NO OTHER WARRANTY OR CONDITION, WHETHER WRITTEN

OR ORAL IS EXPRESSED OR IMPLIED AND AGILENT TECHNOLOGIES

SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OR

MERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A

PARTICULAR PURPOSE.

8. Agilent Technologies will be liable for damage to tangible property per incident up to the

greater of $300,000 or the actual amount paid for the product that is the subject of the

claim, and for damages for bodily injury or death, to the extent that all such damages are

determined by a court of competent jurisdiction to have been directly caused by a defective

Agilent Technologies product.

9. TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY

STATEMENT ARE CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS

INDICATED ABOVE, IN NO EVENT WILL AGILENT TECHNOLOGIES OR ITS

SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL,

INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR OTHER

DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.

FOR CONSUMER TRANSACTIONS IN AUSTRALIA AND NEW ZEALAND: THE

WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT

LAWFULLY PERMITTED, DO NOT EXCLUDE RESTRICT OR MODIFY AND ARE IN

ADDITION TO THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE

OF THIS PRODUCT TO YOU.

ASSISTANCE

Product maintenance agreements and other customer assistance agreements are

available for Agilent Technologies products. For any assistance, contact your nearest

Agilent Technologies Sales and Service Office.

S:\Hp8960\Generic Documents\Manual Operation Getting Started Guide\Pi_manual operation getting started guide\chapters\titlepage.fm

Service and Support

Any adjustment, maintenance, or repair of this product must be performed by

qualified personnel. Contact your customer engineer through your local Agilent

Technologies Service Center. You can find a list of local service representatives on the

Web at:

http://www.agilent-tech.com/services/English/index.html

If you do not have access to the Internet, one of these centers can direct you to your

nearest representative:

United States Test and Measurement Call Center

(Toll free in US)

(800) 452-4844

Europe

(31 20) 547 9900

Canada

(905) 206-4725

Japan Measurement Assistance Center

(81) 426 56 7832

(81) 426 56 7840 (FAX)

Latin America

(305) 267 4288 (FAX)

Australia/New Zealand

1 800 629 485 (Australia)

0800 738 378 (New Zealand)

Asia-Pacific

(852) 2599 7777

(852) 2506 9285 (FAX)

S:\Hp8960\Generic Documents\Manual Operation Getting Started Guide\Pi_manual operation getting started guide\chapters\titlepage.fm

Regional Sales Offices

United States of America:

Agilent Technologies (tel) 1 800 452 4844

Test and Measurement Call Center

P.O. Box 4026

Englewood, CO 80155-4026

Canada:

Agilent Technologies Canada Inc. (tel) 1 877 894 4414

2660 Matheson Blvd. E

Mississauga, Ontario

L4W 5G1

Europe:

Agilent Technologies (tel) (3120) 547 9999

European Marketing Organization

P. O. B o x 9 9 9

1180 AZ Amstelveen

The Netherlands

Japan:

Agilent Technologies Japan Ltd. (tel) (81) 456-56-7832

Measurement Assistance Center (fax) (81) 426-56-7840

9-1 Takakura-Cho, Hachioji-Shi,

Tokyo 192-8510, Japan

Latin America:

Agilent Technologies (tel) (305) 267 4245

Latin America Region Headquarters (fax) (305) 267 4286

5200 Blue Lagoon Drive,

Suite #950

Miami, Florida 33126

U.S. A.

S:\Hp8960\Generic Documents\Manual Operation Getting Started Guide\Pi_manual operation getting started guide\chapters\titlepage.fm

Australia/New Zealand:

Agilent Technologies Australia Pty Ltd. Australia New Zealand

347 Burwood Highway (tel) 1 800 629 485 (tel) 0 800 738 378

Forest Hill, Victoria 3131 (fax) (61 3) 9272 0749 (fax) (64 4) 802

6881

Asia Pacific:

Agilent Technologies(tel) (852) 3197 7777

24/F, Cityplaza One,(fax) (852) 2506 9233

111 Kings Road,

Taikoo Shing, Hong Kong

Altri manuali per 8960

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Agilent Technologies Apparecchiature di prova

Agilent Technologies

Agilent Technologies 86100A Come usare

Agilent Technologies

Agilent Technologies 54835A Manuale utente

Agilent Technologies

Agilent Technologies 54641A Manuale utente

Agilent Technologies

Agilent Technologies 85050C Manuale

Agilent Technologies

Agilent Technologies 1142A Manuale utente

Agilent Technologies

Agilent Technologies InfiniiVision 4000 X-Series Manuale utente

Agilent Technologies

Agilent Technologies 16442A Manuale utente

Agilent Technologies

Agilent Technologies 87075C Option H08 Manuale

Agilent Technologies

Agilent Technologies N9360A Manuale utente

Agilent Technologies

Agilent Technologies Agilent 34980A Manuale utente

Agilent Technologies

Agilent Technologies 85056D Manuale

Agilent Technologies

Agilent Technologies BERT N4901A Manuale utente

Agilent Technologies

Agilent Technologies 1153A Guida alla risoluzione dei problemi

Agilent Technologies

Agilent Technologies U1610/20A Manuale utente

Agilent Technologies

Agilent Technologies N5341A Manuale utente

Agilent Technologies

Agilent Technologies XX3625 Manuale utente

Agilent Technologies

Agilent Technologies ProBER 2 Manuale utente

Agilent Technologies

Agilent Technologies 11644A Series Manuale

Agilent Technologies

Agilent Technologies 81250 Manuale utente

Agilent Technologies

Agilent Technologies E5022B Manuale del proprietario

Agilent Technologies

Agilent Technologies Auroraduet N1726A Manuale utente

Agilent Technologies

Agilent Technologies auroraSonata Manuale utente

Agilent Technologies

Agilent Technologies 87050A Option K24 Manuale

Agilent Technologies

Agilent Technologies U1583A Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuale utente

Ritmix

Ritmix RAT-701 Manuale utente