Draper P5 Manuale utente

SMOOTHING PLANE

■STOCK No.57590 ■PART No.P5

05/99

• INSTRUCTIONS •

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE

THE SAFE AND EFFECTIVE USE OF THIS TOOL.

COMPONENTS

Fig.1

APPLICATION SMOOTHING PLANE:

For finishing, and general purpose work.

Lift lever cam (17) (Fig.1) and remove

lever cap (16) (Fig.1). Remove the cap

iron and cutting iron (8/9) (Fig.1) and

place on bench. Slacken cap iron screw

(15) (Fig.1) (see Fig.2). Slide back cap,

turn and remove. Iron is now ready for

honing.

IMPORTANT: IRON MUST BE

HONED BEFORE USE.

1. HONING THE IRON

The iron is supplied at a ground

angle of 25˚. Hone on a good

quality, flat oil stone lubricated

with light machine oil.

(a) Place ground 25˚ bevel flat on

oil stone and raise 5˚ to honing

angle of 30˚ (Fig.4).

(b) Hone the bevel along the stone,

until a burr is formed on the

back of the iron.

●For easy honing of plane irons use

Draper HG1 honing guide

Stock No.12400.

HONING THE IRON

PREPARING THE IRON FOR

HONING

BENCH PLANE

Fig.2

Fig.3

Fig.4

with bevel upwards (Fig.5).A

few light strokes along the

stone will remove the burr.

The shape of the honed edge

depends on the final use to

which the plane is to be put.

Straight with round corners for

finishing work (Fig.6) and

curved for coarse stock

removal (Fig.7).

2. GRINDING THE IRON

Re-grinding will become necessary if the edge is damaged, the

bevel rounded or the angle changed.Wet stone grinding is

recommended to prevent overheating.

Follow procedure described in the

‘preparing the iron for honing’

section in reverse order. For general

purpose work, the cap iron (9) (Fig.1)

can be positioned approximately

1mm from the cutting edge on the flat

side of the iron. For very hard or very

soft timber, the cap may be set

respectively nearer or farther away

from the cutting edge as required

(see Fig.8).

SETTING THE CAP IRON

Fig.5

Fig.6

Fig.8

Fig.7

The size of the mouth opening (Fig.9)

depends on the use to which the

plane will be put. Fine cabinet work

requires a small mouth; general

purpose work requires a larger

mouth, (as factory setting).

* Remove lever and double iron.

* Slacken frog clamping screws.

* Replace double iron and lever.

* Adjust iron to correct depth (see ‘adjusting the plane’ section).

* Apply hand pressure to move the frog.

* Hold the desired frog position, while removing the lever cap and

double iron, then re-tighten frog clamping screws (7) (Fig.1).

1. DEPTH CUT

Hold the plane as in Fig.10. Adjust

the depth or iron protruding

through the mouth, by turning the

depth adjusting nut (4) (Fig.1),so

that the amount showing is

approximately the thickness of a

hair.

2. ALIGNMENT

Sight down the base and move

lateral adjusting lever (1) (Fig.1),

(See Fig.11).

ADJUSTING THE PLANE

PREPARING THE PLANE

Fig.9

Fig.10

Fig.11

* To improve iron performance, it is

recommended that the procedure

described in the ‘iron sharpening’

section (C) is used to “back-off” or

polish the flat surface of the iron

prior to honing.

* After removing the burr, see ‘iron

sharpening’ section, strop the edge

with a piece of leather, or draw the

edge through a piece of softwood.

* Keep iron very sharp.

* Keep plane base in line with workpiece.

* Set to minimum shaving thickness.

* Plane in same direction as the grain.

* Work from edge to middle when planing end-grain.

* Keep bright parts oiled when not in use.

* Do not clear shavings from mouth with a metallic object.

* To protect iron, always lay plane on side when not in use.

* Do not drop.

1. PROBLEM:

Mouth jams with shaving.

REMEDY:

Too coarse a cut, reset depth of

cut. Poorly fitted cap results in

shavings passing between cap and

iron, re-grind cap edge on oil

stone (Fig.13).

PLANE PROBLEM SOLVING

TIPS AND MAINTENANCE

Fig.12

Fig.13

2. PROBLEM:

“Chatter” marks on work surface

(Fig.14).

REMEDY:

Check frog clamping screws.

Check lever cap pressure on iron.

Check seating of iron on frog face.

3. PROBLEM:

“Tram” lines or scoring marks on

work surface (Fig.15).

REMEDY:

corners of iron too sharp should

be honed to a radius. Iron may be

hollow on edge. Iron may be

damaged, re-hone or re-grind.

Lateral adjustment poorly set.

4. PROBLEM:

Plane skids over surface.

REMEDY:

Iron may be dull and require sharpening. Clean base with solvent.

Check depth of cut.

Fig.14

Fig.15

DRAPER TOOLS LIMITED,

Hursley Road, Chandler's Ford,

Eastleigh, Hants. SO53 1YF. England.

Tel: (01703) 266355.

Fax: (01703) 260784.

No part of this publication may be reproduced,

stored in a retrieval system or transmitted in

any form or by any means, electronic, mechanical

photocopying, recording or otherwise without prior

permission in writing from Draper Tools Ltd.

YOUR DRAPER STOCKIST

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Draper Utensili

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

BGS technic

BGS technic 8578 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare