Flashforge DREAMER Manuale utente

This guide is only applicable to FLASHFORGE Dreamer 3D printer

The User Guide is in the SD card.

USERGUIDE

2. Hot! Avoid touching the heating nozzle in operation.

3. Moving parts in printer may cause injury. Do not wear gloves

or other sources of entanglement in operation.

WARNING 1. Do not remove the wrapping around the nozzle.

DREAMER

Quick Start Guide

SZ01-EN-A02

Kit Contents

3D Printer Filament Spool x 2 Lid After-sales Service Card

Power Cable USB Cable

Quick Start Guide

Build Tape x 2 Leveling Card

Extruder’s

Accessory Kit

Do Not Touch 请勿触摸

CAUTION

注意 1.Extruder hot during operation.

使用过程中喷头会发热。

2.Heating plate hot during operation. Allow surface to cool before servicing.

使用过程中加热平台会发热，待平台表面冷却后再操作。顺时针旋转螺母

升高打印平台。

即减少平台与喷嘴之间

的距离。

逆时针旋转螺母

降低打印平台。

即增加平台与喷嘴之间

的距离。

调整平台支架下方的螺母，直至纸片在喷嘴与平台间的

运动感受到轻微的阻力。

打印平台调节专用

扫描二维码，观看调平指导视频！

Spool Holder x 2

Side Panel x 2 Tool Box

Tool Box Contents:

SD Card / Tweezer / Graver / Scraper / Screw Box* / Wrench / Grease

Allen Wrench / Phillips Screwdriver / Wrench / Unclogging Pin Tool

Extruder’s Accessory Kit Contents:

M3 x 8 Bolt x 2 / M3 x 6 Bolt / Turbofan Baffle

*Screw Box Contents: PTFE tube, Screws, Leveling Knob

Getting to Know Your Dreamer

1.Extruder Cable Bunch 2.Filament Guide Tube 3.Y-Axis Guide Rod 4.X-Axis Guide Rod

5.Build Plate 6.Build Platform 7.Bracket 8.LevelingKnob

9.Z-Axis Guide Rod 10.Touch Screen 11.Cooling Fan 12.Spring Presser

13.Turbofan 14.Turbofan Baffle 15.Left Nozzle

18.SD Card Slot 19.USB Input 20.Reset Button

21.Power Switch 22.Power Input

17.Side Panel

18 19 20 21

910

14 15 16

15.Right Nozzle

Unpacking

1. Open box and remove bag containing the lid,

Quick start guide, After-sales service card,

levelling card, and two build tapes.

2. Take the power cable and two top foam

sheets out.

3. Firmly grasp the two sides handles of

Dreamer. Lift it out from the carton and place

it on a stable surface. Then you will see the

Toolbox and USB cable in the shipping box.

4. Remove the packing bag.(Tip:Save your

packaging for future transportation and

storage.)

5. Take foam out of the dreamer. 6. Open box. Box includes dual extruder, side

panel x 2, extruder's accessory kit. Take the

dual extruder out and place it onto a clean

surface. Notes: Extruder cable bunch is short.

Please do not leave the extruder hanging by

the cable.

7. Remove the bubble wrap from extruder and

slide the X-axis rods to the middle of printer

(A extruder seat on the X-axis).

8. Place the dual extruder on the extruder seat,

as shown.

10. Elevate the build plate to its limit. Notes:

Do not let build plate touch the extruder.

11. Remove both filament rolls and foam pieces

from printer.

Note: Take both spool holders out of the foam.

9. Remove the foam from the back of the logo

board.

12. Lower the build plate fully. Congratulations!

You've unpacked your printer. (Tip: Save

packaging for future transportation and

storage)

Hardware Assembly

Extruder Assembly

1. Place the dual extruder on the extruder

seat.

2. Take the M2.5 Allen Wrench from the tool

box and two M3 x 8 bolts(longer ones)

from the extruder’s accessory kit.

3. Adjust the extruder location to align the

bolt holes.

4. Secure the extruder onto the extruder

seat by screwing the M3 x 8 bolts in. Bolt Hole Bolt Hole

M3 x 8 bolts

X-Axis Guide Rod

Bolt Hole

Turbofan Baffle Assembly

1. Use the M2.5 Allen Wrench to remove two turbofan bolts.

2. Take the turbofan baffle from the extruder’s accessory kit.

3. Install the turbofan baffle to the turbofan.

Bolt Removal

1. Place the turbofan sub-assembly besides the

turbofan seat.

2. Insert the bump on the turbofan seat to the

turbofan sub-assembly.

3. Screw the two bolts in.

4. Take a M3 x 6 bolt from the extruder’s accessory

kit and complete installation according to the

instruction below.

Turbofan Seat

Bolt Mounting

Bolt MountingBolt Mounting

M3X6 Bolt Mounting

Bolt Mounting

Align the bump on the turbofan

seat to the hole in turbofan

sub-assembly.

Leveling Build Platform

How to use the leveling knobs

Raise the build plate to reduce the distance between the nozzle and build plate.

Lower the build plate to increase the distance between the nozzle and build plate.

Rotate knob clockwise

Rotate knob anticlockwise

Print Preheat Tools

HOME

Filament Level Home Manual

Setting Status About

Language TP Adjust FactoryReset

WIFI

Fan On

Pulley

简体中文

English

繁體中文

日本語

Français

Deutsch

Back Fan

Disable

Filament

Check ON

How to change language

How to level the build plate

1. Tighten the three leveling knobs under the build platform until you cannot tighten them any more.

2. Tap [Tools], [Leveling] to start leveling.

3. The build plate and the nozzle start moving, once they suspend, you need to adjust the corresponding

knob under the right nozzle.

4. The leveling card should slide between the nozzle and build plate with some friction/resistance. If the

card slides through easily, the nozzle and build plate are too far apart. Rotate the knob clockwise to

decrease the distance between them. If the card cannot slide through, rotate the knob anticlockwise.

5. After leveling the first point, tap [OK] to continue to the next point.

6. After adjusting the three knobs and making a check when the nozzle is at the center of the plate, you

finish the build plate leveling.

Take the proper distance between

the right nozzle and build plate

as the standard.

Altri manuali per DREAMER

Indice

Altri manuali Flashforge Stampante 3D

Flashforge

Flashforge Inventor II Manuale utente

Flashforge

Flashforge ADVENTURER 3 Manuale utente

Flashforge

Flashforge Finder Manuale utente

Flashforge

Flashforge Finder Manuale utente

Flashforge

Flashforge Inventor Manuale utente

Flashforge

Flashforge Guider Manuale utente

Flashforge

Flashforge Cura Manuale

Flashforge

Flashforge Adventurer 3 Pro 2 Manuale utente

Flashforge

Flashforge Hunter Manuale utente

Flashforge

Flashforge Finder Manuale utente

Flashforge

Flashforge Invertor II Manuale utente

Flashforge

Flashforge Inventor Manuale utente

Flashforge

Flashforge Finder Manuale utente

Flashforge

Flashforge DREAMER Manuale utente

Flashforge

Flashforge EN-A01 Manuale utente

Flashforge

Flashforge DREAMER Manuale utente

Flashforge

Flashforge Foto 13.3 Manuale utente

Flashforge

Flashforge Adventurer 5M Manuale utente

Flashforge

Flashforge Hunter Manuale utente

Flashforge

Flashforge ADVENTURER 3 Manuale utente

Flashforge

Flashforge THOR500T Manuale utente

Flashforge

Flashforge Finder Manuale utente

Flashforge

Flashforge Guider 2 Manuale utente

Flashforge

Flashforge Finder Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente