Lightolier 4X4 MATRIX SERIES Istruzioni per l’uso

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To

assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTALLATION PROCEDURE FOR: 4X4, 4X9, AND 9X9

MATRIX SERIES RECESSED DOWNLIGHTS.

INSTRUCTION SHEET NO.

IS:4X4

B0502

Page 1 of 2

A COMPANY

631 Airport Road, Fall River, MA 02720

°°

A. FRAME-IN AND WIRE-IN

Install FRAME-IN KIT (FIK) using ADJUSTABLE MOUNTING BRACKETS (Fig.’s 1-3). Fixture must be secured to

structural ceiling members. Connect to supply leads; white fixture lead to neutral (white) supply lead, black fixture

lead to hot supply lead, bare copper and/or green insulated wire(s) must be connected to supply ground. Use

wirenuts (local hardware items). Place all electrical connections in the J-BOX and close cover.

CAUTION: (RISK OF FIRE) DO NOT INSTALL INSULATION ABOVE NOR WITHIN 3 INCHES (76mm) OF ANY

PART OF THE LUMINAIRE (FIXTURE)

CAUTION: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURERS’ REFLECTOR

TRIMS MAY VOID THE UNDERWRITERS LABRATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.

ANCHOR CLIP

MOUNTING BAR

T-BAR

WIRE

FIG. 4

FIG. 5

For suspended T-bar ceilings: T-bar ANCHOR CLIPS

accessory No. 1956 (order separately) may be used with

18” or 27” MOUNTING BARS (Fig. 4), or simply wire

MOUNTING BARS, EMT TUBING, or CHANNELS to

ceiling members (Fig. 5).

FIK must be securely attached to and unable to lift from

ceiling members after installation is complete.

For wood joist construction: Mounting bars may be

used to secure FIK. to joists (Fig. 6). MOUNTING BARS

may be bent where required to allow precise placement

of FIK between joists. Use nails to secure to joists.

ADJUSTMENT

SCREW

ADJUSTMENT

SCREW ADJUSTMENT

SCREW

FIK.

HOUSING

ADJUSTABLE

MOUNTING

BRACKET

MOUNTING

BAR

3/4” OR 1-1/2”

CHANNEL

(BY OTHERS)

1/2” EMT

(11/16” OD)

(BY OTHERS)

ADJUSTABLE

MOUNTING

BRACKET

ADJUSTABLE

MOUNTING

BRACKET

FIG. 1

FIG. 2

FIG. 3

FIK.

HOUSING

FIK.

HOUSING

BALLAST

MOUNTING BAR

J-BOX

NAILS

JOISTS

MOUNTING BAR ordering information:

18” long: Cat. No. 1950

27” long: Cat. No. 1951

Note: If FIK is to be used with a WALL-WASH LOUVER TRIM

(Fig. 7), FIK must be installed with either J-BOX side or

BALLAST side parallel to wall to be washed.

Direction of wall to be washed

FIG. 6

FIG. 7

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To

assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:4X4

B0502

Page 2 of 2

A COMPANY

631 Airport Road, Fall River, MA 02720

°°

B. ADJUST FIK

Set FIK so that bottom edge is flush to, or

recessed 1/8” above finished ceiling (Fig. 8).

Final vertical adjustment may be made by means of

ADJUSTMENT SCREWS on inside of FIK.

C. CLOSE-IN

Close-in and finish ceiling as required.

D. INSTALLATION OF REFLECTOR TRIM

1. Squeeze both TORSION SPRINGS and insert ends into

EMBOSSED SLOTS.

2. Push REFLECTOR TRIM up into FIK until flange is seated firmly

againstceilingsurface.

**Care and Maintenance of “Alzak” REFLECTOR TRIM finish:**

If handling of REFLECTOR TRIM with anodized or Alzak finish is required, the

use of clean white or plastic film gloves is recommended to avoid fingerprints.

Anodized or Alzak surfaces can be cleaned by the following methods:

1. Wipe off with a soft, clean, dry, lint-free cloth.

2. Wipe off with a soft clean cloth dampened in mild detergent solution.

Rinse, then wipe dry with lint-free cloth or paper towel.

3. Wipe off with a clean cloth dampened with a solution of wetting agent and

water (such as 2 oz. Per gallon “Pluronic L62-LF” by Wyandotte Products).

Wipe dry.

4. Use a liquid wax such as Glass Wax. Avoid gritty cleaning agents.

E. RE-LAMPING

1. Turn off power

2. Pull REFLECTOR TRIM down until ends of TORSION

SPRINGS reach EMBOSSED SLOTS.

3. Squeeze TORSION SPRINGS to disengage from EMBOSSED

SLOTS, and remove REFLECTOR TRIM.

4. Replace lamp (Do not exceed maximum wattage marking).

5. Replace REFLECTOR TRIM.

F. BALLAST REPLACEMENT

1. Make sure AC power isOFF at fuse-box.

2. Remove REFLECTOR TRIM & lamp(s) (SeeE.).

3. Undo WINGNUT(s) and remove UPPER REFLECTOR.

4. Remove NUTS that secure BALLAST PLATE to HOUSING.

5. Partially remove BALLAST PLATE from HOUSING.

6. Disconnect wire leads from BALLAST push-in terminals.

(Insert pin or paper clip in RELEASE SLOT, Fig. 11)

7. Remove BALLAST from BALLAST PLATE, and install new

BALLAST.

8. Insert wire leads into BALLAST. Follow wiring diagram on

BALLAST.

9. Reattach BALLAST PLATE, UPPER REFLECTOR, lamp(s),

and REFLECTOR TRIM.

BALLAST

PLATE

FIG. 12

FIG. 11

RELEASE

SLOT

UPPER

REFLECTOR

NUTS

HOUSING

WINGNUT

TORSION

SPRING

EMBOSSED

SLOT

REFLECTOR

TRIM

FIG. 10

BALLAST

PLATE

ADJUSTABLE

MOUNTING

BRACKET

FINISHED

CEILING

FLUSH TO CEILING OR

UP TO 1/8” RECESSED

ADJUSTMENT

SCREWS

FIG. 8

FIK

Base of FIK is provided with a

hole pattern (Fig. 9) to assist with the

alignment of multiple FIK’s. This hole

pattern will facilitate the use of laser

beams, plumb lines, etc.

FIG. 9

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Lightolier Apparecchio di illuminazione

Lightolier

Lightolier V611 Manuale utente

Lightolier

Lightolier VR PARABOLIC VRA2G16LS26U Manuale utente

Lightolier

Lightolier Lytecaster 1081 Manuale utente

Lightolier

Lightolier Lytespan 8259WH Manuale utente

Lightolier

Lightolier Lytespan 8119 Manuale utente

Lightolier

Lightolier 1101FIC Manuale utente

Lightolier

Lightolier ProSpec 37254 Manuale utente

Lightolier

Lightolier Calculite C6T6A-MHT6RF Manuale utente

Lightolier

Lightolier Calculite C4P20L Manuale utente

Lightolier

Lightolier Lytespan 6355 Manuale utente

Lightolier

Lightolier Calculite GW Manuale utente

Lightolier

Lightolier Brisa FB9314UDA Manuale utente

Lightolier

Lightolier Paraplus II PPH2G12FW228 Manuale utente

Lightolier

Lightolier H9S2GLR254 Manuale utente

Lightolier

Lightolier ProSpec 26383W Manuale utente

Lightolier

Lightolier 8279EN Manuale utente

Lightolier

Lightolier Calculite ProSpec PA1P3075 Manuale utente

Lightolier

Lightolier C6CW SERIES Manuale utente

Lightolier

Lightolier QVS2GPFOS332 Manuale utente

Lightolier

Lightolier Calculite ProSpec PA4A1175 Manuale utente

Lightolier

Lightolier Lytespan 8680 Manuale utente

Lightolier

Lightolier 48339ALU Manuale utente

Lightolier

Lightolier ProSpec Track Lighting Manuale utente

Lightolier

Lightolier Lytecaster 1135 Manuale utente

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

ArtFox

ArtFox Beam 15R extreme Manuale utente

GLG

GLG multispot 330 Manuale utente

Home Accents Holiday

Home Accents Holiday TY052-1924-1 Manuale utente

SELF Electronics

SELF Electronics FLEX Manuale utente