Stratus SAE-F12X Guida

Stratus 2 Post Base Plate Li Installaon & Operaon & Maintenance Instrucons

Model No.: SAE-F12X

2 Post Base Plate Li

Single (1) Point Manual Release

Liing Capacity: 12000lbs

Installaon & Operaon

Maintenance Instrucons

Important Note

1.This equipment can not be installed ,operated or repaired without reading instrucons.

2.Electricity must be hooked up by cered electrician.

3.Do not use this equipment beyond its rated capacity.

Directory

1-Equipement Descripon………………………………………………………………………………………………3

1.1-Descripon ……………………………………………………………………………………………………………3

1.2-Technical Specicaons………………………………………………………………………………………………3

1.3-Installaon requirement……………………………………………………………………………………………5

2-Specicaons of concrete……………………………………………………………………………………………6

3-Installaon steps………………………………………………………………………………………………………7

4-Check Before Start……………………………………………………………………………………………………16

4.1-Mechanical Installaon Check……………………………………………………………………………………16

4.2-Electrical Hook Up Check…………………………………………………………………………………………16

4.3-Hydraulic System Tesng…………………………………………………………………………………………17

4.4-Load Test……………………………………………………………………………………………………………17

5-Operaon and use …………………………………………………………………………………………………18

5.1-Operaon ……………………………………………………………………………………………………………18

5.2-Raising/Liing ………………………………………………………………………………………………………18

5.3-Stopping………………………………………………………………………………………………………………18

5.4-Lowering………………………………………………………………………………………………………………18

6-Safety……………………………………………………………………………………………………………………18

6.1-Important reminder…………………………………………………………………………………………………18

6.2-Vehicle posion……………………………………………………………………………………………………19

6.3-Risk of Vehicle falling o from the li…………………………………………………………………………19

7-Maintenance……………………………………………………………………………………………………………20

8-Troubleshoong Guide………………………………………………………………………………………………21

9-Structure and Parts List………………………………………………………………………………………………22

9.1-Main column assembly………………………………………………………………………………………………22

9.2-Sub-column assembly………………………………………………………………………………………………23

9.3-Carriage assembly……………………………………………………………………………………………………24

9.4-Hydraulic cylinder assembly…………………………………………………………………………………………25

9.5-Main column safety lock assembly…………………………………………………………………………………26

9.6-Secondary column safety lock assembly……………………………………………………………………………27

9.7-Three-secon arm assembly…………………………………………………………………………………………27

1-Equipement Descripon

1.1-Descripon

This 2Post Floor Plate Li is an advanced car & truck maintenance equipment, mainly used for automove’s

repair and maintenance.

1.2-Technical Specicaons

Model SAE-F12X

Li Capacity 5500KG/12000lbs

Overall Height 3117mm/122 3/4"

Overall Width 3940mm/155 1/8"

Maximum Liing Height 1900mm/74 13/16"

Minimum Height 125mm/4 15/16"

Liing Time About 60 sec.

Outside Column to Outside Column Width 3742mm/147 5/16"

Inside Column Width 3300mm/129 15/16"

Drive Through 2949mm/116 1/8"

Column Thickness of Steel 6mm/0.236"

Carriage Thickness of Steel 6mm/0.236"

Arms Thickness of Steel 8mm/0.315"

Equalized Cable Diameter 9mm/0.354"

Voltage 220V

Power 3.0Kw/4Hp

Breaker 30A

Hydraulic Oil 3-5 Gallons AW32/AW46

Equipment Weight 1980LBS

Installaon (See Fig 1)

Features (See Fig 2)

FIG 1

FIG 2

1.3-Installaon requirement

Tools required

Name Picture

Rotary hammer drill(Φ19)

carpenter's chalk

Hammer

Screw Sets

Level bar

Tap measure

English spanner(12")

Pliers

Ratchet spanner with socket(28#)

Socket head wrench(3#,5#,8#)

Lock wrench

Wrench set(10#,13#,14#,15#,17#,19,24#,27#,30#)

2-Specicaons of concrete ( See Fig 3 )

Specicaons of concrete must be adhered to the specicaon as following. Failure to do so may result in li and/or

vehicle falling.

◇Concrete must be thickness 200mm minimum and without reinforcing steel bars, and must be completely dry be-

fore li installaon.

◇Concrete must be in good condion and must be of test strength 3500psi(245kg/cm²)minimum.

◇Floor must be level with no cracks or holes.

Steps of installaon

◇Locaon of installaon

Check and insure the installaon locaon( concrete, layout, space size etc.) is suitable for li installaon.

◇Use a carpenter's chalk line to establish installaon layout of baseplate( See Fig4).

FIG 3

FIG 4

3-Installaon steps

Step 1:Check the pats before assembly

Packaged li and hydraulic power unit( See Fig 5 )

Step 2:Move aside the parts and check the parts according to the shipment parts list (See Fig 6).

FIG 6

FIG 5

Step 3: Spare parts in the accessories box.

NO. Name Photo Parameter Qty.

1Arm sha Φ40×250L 4

2Arm sha xing screw Countersunk Hexagon Screw M10×15L 4

3Arm boom pad Φ70mm 4

4Increased set Φ60×100L 4

5Heightening bracket 2

6Heightening sleeve bracket xing screw Hexagon socket screws M8×10L 4

7An-collision tape 2

8An-collision rubber strip xing screws Hexagon socket screws M8×30 4

9Power unit frame 1

10 Power unit frame xing screws Hexagon socket screws M10×16L Each 2

11 Power unit xing screws Hexagon Screw M8×25L Each 4

12 Manual unlocking lever M10 Each 1

13 Safety lock release cable 1

14 Wire rope U-shaped chuck M3 2

15 Expansion screw M20×160L 14

16 Plasc gasket 15

17 Plasc cable e 30

18 Main column upper limit switch 1

19 Main column upper limit switch xing

screw

Phillips round head screws M5×10L 2

20 Locking and unlocking rope seat assembly

accessories

21 User’s manual 1

Step 4: Install anchor bolts

Posion the columns on the installaon layout of baseplate. Install the anchor bolts. Check the columns plumbness

with level bar, and adjusng with the shims if the columns are not vercal. Do not ghten the anchor bolts (See Fig 7).

FIG 7

Install Anchor Bolts (Fig 8)

1.Adjust the distance between 2 columns as required dimensions (Fig 8).

2.Adjust the opening direcon of the two columns in a straight line (visible).

3.Install Anchor Bolts (Suggest to use 3/4" Drill).

Note: Don’t Fasten/Tighten Nuts now in case any adjustment needed.

4.Adjust the vercality of the columns (visible) and use U-shape washer (come with package) if necessary.

5.Tighten anchor bolts nuts in diagonal order (Foot Pounds of Torque:90+,suggest to use hand wrench to ghten

nuts.

Note: Anchor bolts driven into the ground at least 150mm.(See Fig 8)

FIG 8

Step 5: Adjust Carriage

Raise the carriage to the 1st locking posion located at the boom of the column (Fig 9).

Note: You can hear‘click’once locked.

Fig 9

Step 6:Install Equalized Cables (2 Cables in total)

Red & Blue color in this Fig are showing how to route the 2 cables (Fig 10).

Fig 10

Indice

Altri manuali Stratus Sistema di sollevamento

Stratus

Stratus SAE-C14X Guida

Stratus

Stratus SAE-C10C Guida

Stratus

Stratus SAE-UT9000 Guida

Stratus

Stratus SAE-UT8000 Guida

Stratus

Stratus SAE-F10P Guida

Stratus

Stratus SAE-P166M Guida

Stratus

Stratus SAE-P48 Guida

Stratus

Stratus SAE-F14X Guida

Stratus

Stratus SAE-C10XE Guida

Stratus

Stratus SAE-C9P Guida

Stratus

Stratus SAE-F10S Istruzioni per l'installazione

Stratus

Stratus SAE-S66M Manuale utente

Stratus

Stratus SAE-C10P Guida

Stratus

Stratus MS9000XT Manuale utente

Stratus

Stratus SAE-P410 Manuale utente

Stratus

Stratus SAE-C12XE Guida

Stratus

Stratus SAE-C12X Guida

Manuali Sistema di sollevamento popolari di altre marche

morse

morse 82H-124 Manuale utente

Braun

Braun NL955 Series Manuale utente

haacon

haacon 1889.10 Manuale utente

Protekt

Protekt AT 252 Manuale utente

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuale utente

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuale utente

Genie

Genie Z-60/34 Manuale utente

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuale utente

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuale utente

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuale di programmazione

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuale di programmazione

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuale di programmazione

BERG

BERG BeNomic EasyLeaf Manuale utente

Powermate

Powermate LiftGate LG-3 Manuale utente

Snorkel

Snorkel TM12 Series Manuale utente

Terberg

Terberg OMNIDEKA Manuale utente

Harmar Mobility

Harmar Mobility AL625 Istruzioni operative

Rotary

Rotary SPO16 Manuale utente