Sylvac UL 4 Manuale utente

INSTRUCTIONS

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUALE D’USO

MODO DE EMPLEO

UL 4

Ultra-light caliper module

Module pied à coulisse ultra-léger

Extra-leichter Messschieber Modul

Modulo calibro a corsoio ultraleggero

Módulo calibre ultraligero

Installing and replacing the battery

Mise en place et remplacement de la

batterie

Einbau und Austausch von Batterie

Installazione e sostituzione della batteria

Colocación y sustitución de la batería

Battery / batterie / batterie / batteria / bateria: lithium 3V, type CR2477 or CR2032 (with adapter, except ULD4)

CR2477

CR2032

Option to use a CR2032 battery with the adapter.

Possibilité d’utiliser une pile CR2032 avec l’adaptateur.

Batterie CR2032 mit Adapter.

Possibilità di utilizzare una pila CR2032 con l’adattatore.

Posibilidad de utilizar una batería CR2032 con el adaptador.

No. 7

or / ou / oder / o / o

No. 1

Adapter for CR2032 (except ULD4)

Outline dimension drawing

Schéma d’encombrement

Masszeichnung

Disegno quotato

Planos dimensionales

1. SET button

2. Favourites button

3. MODE button

4. Battery cover

5. Display

6. Proximity cable housing

1. Measurement unit (mm/INCH)

2. + / - indicator

3. Low battery

4. Active tolerance mode

5. Button locking

6. Preset mode

7. Multiplication factor

8. 6 1/2 digits display

9. Freeze measurement value

10. Bluetooth® connection

11. Send data

12. MIN / MAX / DELTA mode

13. Internal/external measurement indicator

14. Active reference indicator

15. Tolerance indicator

Description of the module

5 6 1

14 13 12 11

7654

1. Operating features of the instrument

- The instrument has two operating modes: rst level functions (direct

access) and second level functions. (see chaps. 3 and 4)

- The «favourite» key gives direct access to one of the most used func-

tions (see chap. 5)

- Sets a Preset value, reset the MIN/MAX mode, applies a selection and

controls switching off the instrument. By default, SIS mode enables au-

tomatic switch-off without any loss of origin (see chap. 7).

1.1 Personalising the functions

It is possible to activate or de-activate some functions of the instrument (see

chap. 9)

1.2 Data transmission parameters

4800Bds, 7 bits, even parity, 2 stop bits

2. Start

Press any button.

SET

MODE

3. First level functions

MODE

SET

Each short press on gives direct access to the rst level functions :

Normal mode : zero reset

Mode int-ext : preset on the measured min or max value

SEt

rEF

PrE

ModE

IntE

toL

Not enabled by default, except in IntE

Choice of reference (REF1, REF2 or automatic REF, see chap. 3.1 Auto ref)

Introduction of a Preset value next digit 0...9 save the Preset

MINIMUM, MAXIMUM and DELTA (TIR) measurement

Tolerance display (introduction of tolerance limits, see chap. 3.2)

Dynamic preset (see chap. 6)

Bluetooth®

function (see chap. 3.3)

rESEt

AMAxAMin

MAC

SET

MODE

Auto

sEt

0.00

SET

IntE

SET

1) not available with Simple prole

3.1 Automatic references

The instrument has the ability to switch automatically between its two references.

This allows using the caliper for both internal and external measuring without

going through the menu to change the reference.

Steps :

On Ref 1

• Introduce a measurement standard as preset, measure this standard and

do a preset recall

• Or set the zero at closed jaws position

On Ref 2

• Measure the internal measurement probes gap (with a caliper, probes

included) and introduce it as preset value

• Do a preset recall at closed jaws position

Set Auto

It is now possible to measure in REF1 when closing the jaws or in REF2 when

opening the jaws.

Remark: for the reference change to work, it is necessary to make a displacement

>0.2mm in the opposite direction.

3.2. Insert tolerance limits

MODE

SET

In order to introduce or modify the tolerance limits, it is necessary to select tol →

On , followed by a short press on

....... Input the lower tolerance limit (e.g. +0019.90 for 20-0.1mm)

.......Input the upper tolerance limit (e.g. +0020.10 for 20+0.1mm)

next digit 0...9 save the tolerance

The connection procedure has been designed to be simple and is signalled by

the following three states:

1° Symbol off................disconnected mode.

2° Symbol blinking .......advertising mode.

3° Symbol on .............. connected mode.

3.3. Bluetooth® conguration

The following options can be selected to control the Bluetooth®module.

On Enable Bluetooth®module (start advertising mode).

OFF Disable Bluetooth®module (terminate active connection).

rESEt Clear pairing information.

MAC Display the MAC (Media Access Control) address.

Three Bluetooth® proles are available.

SIMPLE Prole without pairing (default).

PAIr Paired and secured prole.

HId Virtual keyboard mode (compatible with recent equipement without

driver installation).

Note:

Pairing information are erased while prole is switched.

Note :

- In case of internal measurements, you can cross the indicators by reversing

the order of entering the tolerance intervals (upper interval < lower interval)

- It is possible to introduce different tolerance limits on REF1 and REF2.

- It is also possible to display the tolerance limits when the instrument is working

in MIN, MAX or DELTA (TIR) mode

....... Input the lower tolerance limit (e.g. +0019.90 for 20-0.1mm)

.......Input the upper tolerance limit (e.g. +0020.10 for 20+0.1mm)

next digit 0...9 save the tolerance

3.3.1

Bluetooth

® specication

Frequency Band 2.4GHz (2.402 - 2.480GHz)

Modulation GFSK (Gaussian Frequency Shift Keying)

Max Output Power Class 3: 1mW (0dBm)

Range Open space: up to 15m

Industrial environment: 1-5m

Battery life with CR2477

Continuous : up to 8 months - Always connected with 4 values /sec.

Saver : up to 21 months - The instrument sends value only when the position has changed.

Blind/Push : up to 24 months - Value is sent from the instrument (button) or requested

from the computer.

Other specications on the manufacturer’s website

Connection:

1° Activate Bluetooth®compatible software and hardware (Master : PC,

Display Unit).

2° Start the instrument. By default the Bluetooth®module is active and

the instrument is available for connection (advertising mode).

3° If no connnection is established during the advertisement period, rea-

ctivate the Bluetooth®module using the bt /On menu.

4° Instrument is ready to communicate (connected mode.)

Only with paired prole :

Pairing with master is automatically done at rst connection.

To connect the instrument to a new master (new pairing), pairing information on

the instrument must be cleared using the bt / rESEt menu.

Altri manuali per UL 4

Indice

Lingue:

Altri manuali Sylvac Strumento di misura

Sylvac

Sylvac PS16 V2 Manuale utente

Sylvac

Sylvac S-Mike PRO Manuale utente

Sylvac

Sylvac SCAN F60 Manuale utente

Sylvac

Sylvac 810.9707 Manuale utente

Sylvac

Sylvac Hi Cal 150 Manuale utente

Sylvac

Sylvac Bowers XTL Manuale utente

Sylvac

Sylvac Hi Gage ONE Smart Manuale utente

Sylvac

Sylvac Hi Cal Manuale utente

Sylvac

Sylvac S Depth PRO Manuale utente

Sylvac

Sylvac Scan Series Manuale utente

Sylvac

Sylvac S Mike PRO Manuale utente

Sylvac

Sylvac S_Cal EVO Smart Form E Manuale utente

Sylvac

Sylvac UL 4 Manuale utente

Sylvac

Sylvac S Mike IP67 Manuale utente

Sylvac

Sylvac S_Dial WORK ANALOG Smart Manuale utente

Sylvac

Sylvac S Dial WORK Manuale utente

Sylvac

Sylvac S Dial WORK Smart Manuale utente

Sylvac

Sylvac SYLVAC-SCAN 52 REFLEX-CLICK Manuale utente

Sylvac

Sylvac Fowler Ultra-cal II Manuale utente

Sylvac

Sylvac S Dial WORK ANALOG NANO Smart Manuale utente

Sylvac

Sylvac Hi Cal Manuale utente

Sylvac

Sylvac S Cal EVO Standard Manuale utente

Sylvac

Sylvac PS15 Manuale utente

Sylvac

Sylvac S_Cal EVO Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente