LaserLiner ZipLevel Manuale utente
GB Operation manual
ZipLevel
092.010A/ 092.020A / Rev 1108-GB
ENGLISH
2ENGLISH
ZipLevel
3
ENGLISH
ZipLevel
Professional precision altimeter
The ZipLevel is a professional altimeter which enables you to scale and level
on your own also around corners with accuracy within 3 mm. You have
a working area up to + 6 m vertical and up to 70 m, respectively 50 m
(with ZipLevel 25) in diameter. The digital measuring module shows all your
measurements and is easy to operate. The extremely sturdy measurement
cable with patented gas-liquid-system reliably works from -30 °C up to
+70 °C.
Warranty
The warranty period is 2 years from the date of purchase. The warranty
covers all material or manufacturing defects occurring during this time. The
following are excluded from warranty: Damage due to improper use (e.g.
operation with wrong type of current/voltage, connection to unsuitable
power source, fall onto hard surface, etc.) or improper storage, normal
wear and tear, and defects which only insignificantly impair the value or
suitability for use. Any tampering by unauthorised persons will render this
warranty void. In the event that you need to claim warranty, please take
the complete device together with all information and the invoice to one
of our dealers or send it in to Umarex-Laserliner.
Accessories: Only with the ZipLevel Pro 35 sensing device, cover and
ground spikes are included. For the ZipLevel 25 these accessories are also
available!
ENGLISH
4ENGLISH
ZipLevel
ACable reel
BSecuring points
CMeasurement line
DMeasuring module
EBattery compartment (back)
FRoom for measuring module
GPocket for operation manual
HProtective cap
Backside:
ISensing device (ZipLevel Pro 35)
JGround spikes (ZipLevel Pro 35)
A
C
BD
E
F
G
H
I
J
Inserting batteries into the measuring module:
• Open the battery compartment (E) and insert the batteries according to
the installation symbol. Pay attention to the correct polarity. Close the
battery compartment again. Remove the protective cover (with ZipLevel
Pro 35 only).
Advice: Do not put used batteries into the household rubbish. They can
be handed in at a collecting point for old batteries respectively hazardous
waste
ENGLISH
ENGLISH 5
ENGLISH
Console:
The keys HOLD and ON/OFF react instantaneously, all the other keys have
to be pressed for 2 seconds in order to activate or deactivate the particular
function. The functions are also fitted with audible signals (clicking and
bleeping) which makes it easier to work overhead or in non visible areas.
Important:
The ZipLevel memorizes the last accomplished function. When you turn the
instrument on again and intend to leave the function, press the accordant
key for 2 seconds.
Hold the
Function keys
for 2 seconds!!!
ZipLevel
6ENGLISH
ZipLevel
Quick start of the ZipLevel
Open the bottom protective cap of the basic unit and remove the measu-
ring module. Lay the basic unit on the floor with the back facing down.
Slowly pull a sufficient length of line off the cable reel. The altitude will be
transferred from the basic unit to the measuring module.
Switch the measuring module on with the ON/OFF-key and put the unit
with its back or base on the required place of reference. When the display
is ready, you will hear 2 short audible bleeps. Press the ZERO-key for 2
seconds. Keep the measuring module steady until the figure zero appears
on the display. The appliance has now been set.
ADVICE: If the basic unit gets moved, the measuring module needs to be
set at the place of reference again.
Back facing
down!
Base
Back
ENGLISH
ENGLISH 7
ENGLISH
Quick start of the ZipLevel
Give a place of reference to the measuring module (press ZERO-key) and
move it to a different height. The appliance shows the difference in height
between the place of reference and the measuring point. Now you can
hold the appliance against any point and it always shows you the current
height towards the place of reference.
Always use the measuring module with the side, which was used to set
ZERO. Do not change from one locating side to another without setting to
ZERO again.
If you want to find out the height between floor and ceiling set the app-
liance to ZERO with its back or bottom side on the floor. Then hold the
top, base or back to the ceiling in order to measure. Manually add the
height (8,8 cm) or thickness (5,0 cm) of the measuring module to the
shown data. Take into account whether you are working with protective
cover or not! This feature can also be done automatically with the ADDER-
function (pp. 16-17).
ZipLevel
reference point
measuring point
Typical uses:
8ENGLISH
ZipLevel
Keys and functions
ON/OFF
With this key you switch the unit on and off. If no key has been pressed or
the measuring module has not been moved within 4 minutes, the unit will
switch itself off automatically. After 3 minutes without any activity the unit
will sound a warning by giving 2 long bleeps.
HOLD
The HOLD-function is used where you have problems reading the display
or where you intend to keep the measured data. The function can be
switched on and off by shortly pressing the HOLD-key.
Measuring and keeping of the data (see drawing p. 7):
1) First you set the unit at the required point with the ZERO-key.
2) Shortly press the HOLD-key as long as the measuring module is still
being moved. The unit will then give a series of bleeps.
3) Move the measuring module to the place where you intend to measure.
4) Wait until the unit has stabilized and therefore no more bleeps are
audible.
5) Retrieve the measuring module. The data of the remote point will be
kept on the display. Shortly press HOLD again to leave this function.
ENGLISH
ENGLISH 9
ENGLISH
Examples for the HOLD-function:
ZipLevel
ZERO
Press the ZERO-key for 2 seconds in order to make the present height
(location of the measuring module) the point of reference. The unit must
not be moved in this process!
3 m
Level of reference
New level of reference
1. ZERO
2. Press HOLD
When set zo zero
at the top
- 3 m will be shown
at the bottom
10 ENGLISH
ZipLevel
SCALE
With this you choose the required measurements in millimetres, centime-
tres or meters. Press the SCALE-key for 2 seconds and hold. Now the
gauges the bottom right of the display will change. Release the key once
the required measurement appears. The measurement for millimetres is not
indicated, cm and m appear on the display.
RES
The ZipLevel is featured with a choice of 3 display accuracies. Press the
RES-key for 2 seconds and keep it pressed in order to choose the required
resolution. Release the RES-key once the required resolution is shown.
Your choice is stored now up to next accuracy change.
0,2 cm: for highest accuracy
needs more time to stabilize
0,5 cm: for medium accuracy
needs less time for stabilization
1 cm: for rough measuring
quick stabilizing of the results
ENGLISH
Indice
Altri manuali LaserLiner Strumento di misura
LaserLiner
LaserLiner AutoCross-Laser 2 Plus Manuale utente
LaserLiner
LaserLiner ClimaData Stick Manuale utente
LaserLiner
LaserLiner DampFinder Manuale utente
LaserLiner
LaserLiner CompactLine-Laser G360 Manuale utente
LaserLiner
LaserLiner SmartLine-Laser 360 Manuale utente
LaserLiner
LaserLiner ThermoMaitre Manuale utente
LaserLiner
LaserLiner MultiMeter-Pocket Manuale utente
LaserLiner
LaserLiner MoistureMaster Compact Plus Manuale utente
LaserLiner
LaserLiner ClimaData Box Manuale utente
LaserLiner
LaserLiner PowerCross-Laser 5 Combi Manuale utente
LaserLiner
LaserLiner AirMonitor CO2 Manuale utente
LaserLiner
LaserLiner CoatingTest-Master Manuale utente
LaserLiner
LaserLiner DampMaster Compact Plus Manuale utente
LaserLiner
LaserLiner LaserRange-Master Gi5 Manuale utente
LaserLiner
LaserLiner AirMonitor FRESH Manuale utente
LaserLiner
LaserLiner PowerBright-Laser PBL P5 Manuale utente
LaserLiner
LaserLiner LaserRange-Master T7 Manuale utente
LaserLiner
LaserLiner CombiRangeXtender 40 Manuale utente
LaserLiner
LaserLiner RangeXtender RX 30 Manuale utente
LaserLiner
LaserLiner LaserRange-Master T4 Pro Manuale utente
